How to switch between lines and cuts
Click the knife icon in front of the line layer to switch the layer properties of the line.
Correspondence between depth and speed of line engraving and line cutting
Line Layer
|
line
|
depth(%)
|
speed（mm/s）
|
|
|
100
|
0.8
|
|
|
1
|
80
|
Cut layer
|
cutting
|
depth(%)
|
speed（mm/s）
|
|
|
100
|
0.1
|
|
|
1
|
10
|
Official LX1 recommended parameters:
Line engraving is based on line layers
Line cutting is based on line cutting layers
The operation video is as follows
Line and cutting engraving depth and speed corresponding detailed parameter table
Note:
- The parameters in the green marking area mean that when the parameters in this part are matched with the appropriate engraving power, it is more suitable for engraving.
- The parameters in the pink marking area mean that this part of the parameters is more suitable for cutting when paired with higher engraving power (be careful of the risk of high temperature and fire).
|
line
|
line cutting
|
||||
|
depth(%)
|
speed（mm/s）
|
air pump control
|
depth(%)
|
speed（mm/s）
|
air pump control
|
|
1
|
80
|
level one strength
|
1
|
10
|
secondary strength
|
|
2
|
79.2
|
2
|
9.9
|
||
|
3
|
78.4
|
3
|
9.8
|
||
|
4
|
77.6
|
4
|
9.7
|
||
|
5
|
76.8
|
5
|
9.6
|
||
|
6
|
76
|
6
|
9.5
|
||
|
7
|
75.2
|
7
|
9.4
|
||
|
8
|
74.4
|
8
|
9.3
|
||
|
9
|
73.6
|
9
|
9.2
|
||
|
10
|
72.8
|
10
|
9.1
|
||
|
11
|
72
|
11
|
9
|
||
|
12
|
71.2
|
12
|
8.9
|
||
|
13
|
70.4
|
13
|
8.8
|
||
|
14
|
69.6
|
14
|
8.7
|
||
|
15
|
68.8
|
15
|
8.6
|
||
|
16
|
68
|
16
|
8.5
|
||
|
17
|
67.2
|
17
|
8.4
|
||
|
18
|
66.4
|
18
|
8.3
|
||
|
19
|
65.6
|
19
|
8.2
|
||
|
20
|
64.8
|
20
|
8.1
|
||
|
21
|
64
|
21
|
8
|
||
|
22
|
63.2
|
22
|
7.9
|
||
|
23
|
62.4
|
23
|
7.8
|
||
|
24
|
61.6
|
24
|
7.7
|
||
|
25
|
60.8
|
25
|
7.6
|
||
|
26
|
60
|
26
|
7.5
|
||
|
27
|
59.2
|
27
|
7.4
|
||
|
28
|
58.4
|
28
|
7.3
|
||
|
29
|
57.6
|
29
|
7.2
|
||
|
30
|
56.8
|
30
|
7.1
|
||
|
31
|
56
|
31
|
7
|
||
|
32
|
55.2
|
32
|
6.9
|
||
|
33
|
54.4
|
33
|
6.8
|
||
|
34
|
53.6
|
34
|
6.7
|
||
|
35
|
52.8
|
35
|
6.6
|
||
|
36
|
52
|
36
|
6.5
|
||
|
37
|
51.2
|
37
|
6.4
|
||
|
38
|
50.4
|
38
|
6.3
|
||
|
39
|
49.6
|
39
|
6.2
|
||
|
40
|
48.8
|
40
|
6.1
|
||
|
41
|
48
|
41
|
6
|
||
|
42
|
47.2
|
42
|
5.9
|
||
|
43
|
46.4
|
43
|
5.8
|
||
|
44
|
45.6
|
44
|
5.7
|
||
|
45
|
44.8
|
45
|
5.6
|
||
|
46
|
44
|
46
|
5.5
|
||
|
47
|
43.2
|
47
|
5.4
|
||
|
48
|
42.4
|
48
|
5.3
|
||
|
49
|
41.6
|
49
|
5.2
|
||
|
50
|
40.8
|
50
|
5.1
|
||
|
51
|
40
|
51
|
5
|
||
|
52
|
39.2
|
52
|
4.9
|
||
|
53
|
38.4
|
53
|
4.8
|
||
|
54
|
37.6
|
54
|
4.7
|
||
|
55
|
36.8
|
55
|
4.6
|
||
|
56
|
36
|
56
|
4.5
|
||
|
57
|
35.2
|
57
|
4.4
|
||
|
58
|
34.4
|
58
|
4.3
|
||
|
59
|
33.6
|
59
|
4.2
|
||
|
60
|
32.8
|
60
|
4.1
|
||
|
61
|
32
|
61
|
4
|
||
|
62
|
31.2
|
62
|
3.9
|
||
|
63
|
30.4
|
63
|
3.8
|
||
|
64
|
29.6
|
64
|
3.7
|
||
|
65
|
28.8
|
65
|
3.6
|
||
|
66
|
28
|
66
|
3.5
|
||
|
67
|
27.2
|
67
|
3.4
|
||
|
68
|
26.4
|
68
|
3.3
|
||
|
69
|
25.6
|
69
|
3.2
|
||
|
70
|
24.8
|
70
|
3.1
|
||
|
71
|
24
|
71
|
3
|
||
|
72
|
23.2
|
72
|
2.9
|
||
|
73
|
22.4
|
73
|
2.8
|
||
|
74
|
21.6
|
74
|
2.7
|
||
|
75
|
20.8
|
75
|
2.6
|
||
|
76
|
20
|
secondary strength
|
76
|
2.5
|
|
|
77
|
19.2
|
77
|
2.4
|
||
|
78
|
18.4
|
78
|
2.3
|
||
|
79
|
17.6
|
79
|
2.2
|
||
|
80
|
16.8
|
80
|
2.1
|
||
|
81
|
16
|
81
|
2
|
||
|
82
|
15.2
|
82
|
1.9
|
||
|
83
|
14.4
|
83
|
1.8
|
||
|
84
|
13.6
|
84
|
1.7
|
||
|
85
|
12.8
|
85
|
1.6
|
||
|
86
|
12
|
86
|
1.5
|
||
|
87
|
11.2
|
87
|
1.4
|
||
|
88
|
10.4
|
88
|
1.3
|
||
|
89
|
9.6
|
89
|
1.2
|
||
|
90
|
8.8
|
90
|
1.1
|
||
|
91
|
8
|
91
|
1
|
||
|
92
|
7.2
|
92
|
0.9
|
||
|
93
|
6.4
|
93
|
0.8
|
||
|
94
|
5.6
|
94
|
0.7
|
||
|
95
|
4.8
|
95
|
0.6
|
||
|
96
|
4
|
96
|
0.5
|
||
|
97
|
3.2
|
97
|
0.4
|
||
|
98
|
2.4
|
98
|
0.3
|
||
|
99
|
1.6
|
99
|
0.2
|
||
|
100
|
0.8
|
100
|
0.1
|
||
Comments
0 comments
Article is closed for comments.