How to Switch Between Line Engraving and Line Cutting?
Click the knife icon in front of the line layer to switch the layer properties of the line.
Correspondence Between Depth And Speed of Line Engraving and Line Cutting
Line Layer
|
line |
depth(%) |
speed(mm/s) |
|
|
100 |
0.8 |
|
|
1 |
80 |
Cut layer
|
cutting |
depth(%) |
speed(mm/s) |
|
|
100 |
0.1 |
|
|
1 |
10 |
Note
Line engraving is based on line layers
Line cutting is based on cut layers
The operation video is as follows
Line Engraving and Line Cutting Depth And Speed Corresponding Parameter Table
Note:
- The parameters in the green marking area mean that when the parameters in this part are matched with the appropriate engraving power, it is more suitable for engraving.
- The parameters in the red marking area mean that this part of the parameters is more suitable for cutting when paired with higher engraving power (be careful of the risk of high temperature and fire).
|
line Engraving |
line cutting |
||||
|
depth(%) |
speed(mm/s) |
air pump control |
depth(%) |
speed(mm/s) |
air pump control |
|
1 |
80 |
level one strength
|
1 |
10 |
secondary strength
|
|
2 |
79.2 |
2 |
9.9 |
||
|
3 |
78.4 |
3 |
9.8 |
||
|
4 |
77.6 |
4 |
9.7 |
||
|
5 |
76.8 |
5 |
9.6 |
||
|
6 |
76 |
6 |
9.5 |
||
|
7 |
75.2 |
7 |
9.4 |
||
|
8 |
74.4 |
8 |
9.3 |
||
|
9 |
73.6 |
9 |
9.2 |
||
|
10 |
72.8 |
10 |
9.1 |
||
|
11 |
72 |
11 |
9 |
||
|
12 |
71.2 |
12 |
8.9 |
||
|
13 |
70.4 |
13 |
8.8 |
||
|
14 |
69.6 |
14 |
8.7 |
||
|
15 |
68.8 |
15 |
8.6 |
||
|
16 |
68 |
16 |
8.5 |
||
|
17 |
67.2 |
17 |
8.4 |
||
|
18 |
66.4 |
18 |
8.3 |
||
|
19 |
65.6 |
19 |
8.2 |
||
|
20 |
64.8 |
20 |
8.1 |
||
|
21 |
64 |
21 |
8 |
||
|
22 |
63.2 |
22 |
7.9 |
||
|
23 |
62.4 |
23 |
7.8 |
||
|
24 |
61.6 |
24 |
7.7 |
||
|
25 |
60.8 |
25 |
7.6 |
||
|
26 |
60 |
26 |
7.5 |
||
|
27 |
59.2 |
27 |
7.4 |
||
|
28 |
58.4 |
28 |
7.3 |
||
|
29 |
57.6 |
29 |
7.2 |
||
|
30 |
56.8 |
30 |
7.1 |
||
|
31 |
56 |
31 |
7 |
||
|
32 |
55.2 |
32 |
6.9 |
||
|
33 |
54.4 |
33 |
6.8 |
||
|
34 |
53.6 |
34 |
6.7 |
||
|
35 |
52.8 |
35 |
6.6 |
||
|
36 |
52 |
36 |
6.5 |
||
|
37 |
51.2 |
37 |
6.4 |
||
|
38 |
50.4 |
38 |
6.3 |
||
|
39 |
49.6 |
39 |
6.2 |
||
|
40 |
48.8 |
40 |
6.1 |
||
|
41 |
48 |
41 |
6 |
||
|
42 |
47.2 |
42 |
5.9 |
||
|
43 |
46.4 |
43 |
5.8 |
||
|
44 |
45.6 |
44 |
5.7 |
||
|
45 |
44.8 |
45 |
5.6 |
||
|
46 |
44 |
46 |
5.5 |
||
|
47 |
43.2 |
47 |
5.4 |
||
|
48 |
42.4 |
48 |
5.3 |
||
|
49 |
41.6 |
49 |
5.2 |
||
|
50 |
40.8 |
50 |
5.1 |
||
|
51 |
40 |
51 |
5 |
||
|
52 |
39.2 |
52 |
4.9 |
||
|
53 |
38.4 |
53 |
4.8 |
||
|
54 |
37.6 |
54 |
4.7 |
||
|
55 |
36.8 |
55 |
4.6 |
||
|
56 |
36 |
56 |
4.5 |
||
|
57 |
35.2 |
57 |
4.4 |
||
|
58 |
34.4 |
58 |
4.3 |
||
|
59 |
33.6 |
59 |
4.2 |
||
|
60 |
32.8 |
60 |
4.1 |
||
|
61 |
32 |
61 |
4 |
||
|
62 |
31.2 |
62 |
3.9 |
||
|
63 |
30.4 |
63 |
3.8 |
||
|
64 |
29.6 |
64 |
3.7 |
||
|
65 |
28.8 |
65 |
3.6 |
||
|
66 |
28 |
66 |
3.5 |
||
|
67 |
27.2 |
67 |
3.4 |
||
|
68 |
26.4 |
68 |
3.3 |
||
|
69 |
25.6 |
69 |
3.2 |
||
|
70 |
24.8 |
70 |
3.1 |
||
|
71 |
24 |
71 |
3 |
||
|
72 |
23.2 |
72 |
2.9 |
||
|
73 |
22.4 |
73 |
2.8 |
||
|
74 |
21.6 |
74 |
2.7 |
||
|
75 |
20.8 |
75 |
2.6 |
||
|
76 |
20 |
secondary strength
|
76 |
2.5 |
|
|
77 |
19.2 |
77 |
2.4 |
||
|
78 |
18.4 |
78 |
2.3 |
||
|
79 |
17.6 |
79 |
2.2 |
||
|
80 |
16.8 |
80 |
2.1 |
||
|
81 |
16 |
81 |
2 |
||
|
82 |
15.2 |
82 |
1.9 |
||
|
83 |
14.4 |
83 |
1.8 |
||
|
84 |
13.6 |
84 |
1.7 |
||
|
85 |
12.8 |
85 |
1.6 |
||
|
86 |
12 |
86 |
1.5 |
||
|
87 |
11.2 |
87 |
1.4 |
||
|
88 |
10.4 |
88 |
1.3 |
||
|
89 |
9.6 |
89 |
1.2 |
||
|
90 |
8.8 |
90 |
1.1 |
||
|
91 |
8 |
91 |
1 |
||
|
92 |
7.2 |
92 |
0.9 |
||
|
93 |
6.4 |
93 |
0.8 |
||
|
94 |
5.6 |
94 |
0.7 |
||
|
95 |
4.8 |
95 |
0.6 |
||
|
96 |
4 |
96 |
0.5 |
||
|
97 |
3.2 |
97 |
0.4 |
||
|
98 |
2.4 |
98 |
0.3 |
||
|
99 |
1.6 |
99 |
0.2 |
||
|
100 |
0.8 |
100 |
0.1 |
||
LX1 Recommended Parameter Link
Related to